***All seam allowances are ¼”.***
***Read the entire recipe before starting. By doing this, you will learn how to make both the play mat and the changing pad simultaneously.
***It may not be a bad idea to use a stronger 90/14 needle since it gets quite congested in the middle of the quilt towards the end. I used an 80/12 needle for both of these quilts, but on another play mat I made, I used an 80/12 needle and it broke when I got to the center of the quilt (when the quilt was almost complete), flew at me, and almost took my eye out. …just sayin’!***
Creating the Play Mat
1. Cut the entire Jelly Roll in half, creating 80 (2 ½” x 22″) strips.
2. Set out all your strips in a circular pattern to determine your sewing order. For the play mat, you will need approx. 68 strips. (You’ll need to set aside 3 additional colored strips for your changing pad.)
3. Choose your first strip and lay it right side up on your cutting mat.
4. Cut the strip diagonally lengthwise starting at the top right corner and cutting to ¼” over from the bottom left corner (I know this sounds confusing so I’ve taken a close-up photo below for a visual aid). This ¼” provides the necessary seam allowance for attaching the next strip. Make sure the selvage is always the widest part of your strip (this will be the outside edge of the quilt(s)) when you both cut and sew. On second thought, it would be pretty cool to put your selvages toward the center of your quilt so the middle could scream “Mo Mo, Mo Mo, Mo Mo!”
5. Here is what the first piece looks like after it’s cut.
|The piece of the left will be used for the play mat,
the scrap on the right will be used for the changing pad.
9. Place the two pieces you’ve sewn together right side up on your cutting mat. Cut the second strip (on the right) as you did in step 4 (above), starting from the top right corner and cutting on the diagonal down the length of the strip to ¼” over from the bottom left corner of the second strip.
10. With right sides together, sew the third full strip to the second diagonal piece.
11. Press seams open.
12. Place the three pieces you’ve sewn together right side up on your cutting mat. Again, cut the third strip (the strip on the right side) as you did in Step 4, starting at the top right corner and cutting on the diagonal to the bottom left corner, leaving ¼” seam allowance intact.
|Make sure to always leave 1/4″ in the center when cutting off your scrap strip.|
15. After you have sewn the last strip to the first, press the seams open. As you will notice, the middle gets a little crazy. When pressing, don’t worry about the middle so much. Let it go where it wants to go. Just make sure to press the seams open as well as you can on the outer portion of the quilt.
16. Your play mat will now look like this.
18. When binding, make sure to cut your binding on the bias for maximum smoothness around the curves.
The changing pad is a breeze to make because your strips are already cut into triangles. As scraps are cut from the play mat, you can start sewing them together to make this changing pad. Each time you cut a new scrap, immediately sew it onto the changing pad. If you do it this way, you will be pleasantly surprised to have two completed quilt tops finished at the exact same time. Keep in mind, the changing pad uses 3 more strips than the play mat, so if you want to add a strip into the changing mat at a specific spot, other than at the end, be aware of it while you are sewing and don’t forget to add it in. I just added my three extra strips at the very end. I know it doesn’t seem logical that the smaller changing pad uses more strips than the larger play mat, but it really does. Here is a picture of what it will look like when you’ve finished the play mat and still need to add the 3 strips to the changing pad.
4. Press seams open.
5. Turn the two pieces you’ve sewn together right side up. If you’ll notice, the strip on the right looks a little wavy. You’ll want to straighten’er up.
6. With right sides together, sew the third strip to the second diagonal piece. The pinked edge of the top piece (strip 3) should be on the right side.
7. Press seams open.
8. Turn the three sewn pieces right side up on your cutting mat. Trim the strip up as you did before removing any waviness. Make sure to leave your 1/4″ seam allowance at the bottom.